What did you do to your Z this week? | Page 172 | The Z Club of Great Britain
  1. The Z Club relies on the support of it's paid members - join the club or renew your membership here.

What did you do to your Z this week?

Discussion in 'General discussion' started by jonbills, Apr 11, 2017.

  1. M-j-b

    M-j-b
    Z Club Member

    Finally ...... have finished all of the suspension, underbody prep etc to send the car off for paint.

    All glass out, the only thing left on the entire vehicle is the dash (suspension etc will come off at the body shop)

    A massive milestone for me !!

    Rolling shell being collected Saturday morning :)
     
    Jason McIvor, franky, atomman and 2 others like this.
  2. status

    status Well-Known Forum User

    Washed mine using one of those towels the detailers use,bloody amazing,less than 10 mins
    Getting it ready for fourways then putting it away noticed a tyre was a bit low so getting out in a min to hopefully pump it up,fingers x
     
  3. MaximG

    MaximG
    Z Club Member

    Finally took it out again to get the tracking done. Took it for a quick spin up and down the A1 after and I have to say she feels bloody great to drive, maybe I will keep her a little longer.

    However after rebuilding the suspension last year with new springs and shocks the back of the car is sitting high. I don't know if its the new springs, the new shocks, a combination of both. I do know one thing I've kind of lost the will to investigate and bother fixing it.
     
    tyroguru, franky and jonbills like this.
  4. Rob Gaskin

    Rob Gaskin Treasurer Staff Member Moderator

    Put some weight in the back e.g tool kit, spare wheel (you don't have one do you) and fill the tank.

    I felt like that after working on my blue car. So put the Sam up for sale. Anyway got motivated again, sorted a few jobs and don't feel the same way now.
     
    AliK and MCBladeRun like this.
  5. toopy

    toopy
    Z Club Member

    Nothing to the Z...... as usual :(

    Was planning on popping down to the Fourways open/coffee morning, but needed to change the fuel pressure relief valve on my Transit.

    Done in about half hour, quick test run round the block, felt better behaved but....... opened the bonnet to double check all was ok, and half the engine was covered in diesel!

    Took it off again and the supplied copper washer hadn't seated properly, was fine on idle but while driving!! comparing the washers they weren't quite the same.

    Re-used the old washer which was ever so slightly larger and therefore seated perfectly ( they always say don't re-use washers, but half the time the new ones which aren't oem are shite)

    This time i ran it without the air filter box in the way of viewing any leaks, revved it to be sure, all good, fit air box, test run...... success :)

    So after that kerfuffle, i sat down and drank beer... forgot about fourways...... oops.
     
    AliK and Huw like this.
  6. status

    status Well-Known Forum User

    Missed a good catch up with some old gits like me and a few others,good turn out of zeds
     
  7. AD240Z

    AD240Z
    Z Club Member

    Attached Files:

    atomman, datsfun, Huw and 1 other person like this.
  8. Huw

    Huw
    Z Club Member

    I found an oil leak…… another one
     
    AliK likes this.
  9. jonbills

    jonbills
    ZClub Administrator
    Moderator

    Better than not finding it, I suppose. Where?
     
    AliK likes this.
  10. Huw

    Huw
    Z Club Member

    Blasted rear crank seal …….:mad:
     
  11. datsfun

    datsfun
    Z Club Member

    The 620 for me please.
     
  12. moggy240

    moggy240 INSURANCE VALUATIONS OFFICER Staff Member Moderator

    Fitted my latest rocker cover as my plastic one has a hairline crack.
     

    Attached Files:

    ALN, Tony Mc, tyroguru and 2 others like this.
  13. tyroguru

    tyroguru
    Z Club Member

    Wow Mike, that is bold but goes perfectly with your car. Any idea what the text says (maybe just "Nissan Motor Company")?
     
  14. ben240z

    ben240z
    Z Club Member

    Took it up to the Fourways Engineering coffee morning. Basked in sunshine and surrounded by amazing cars. Needed more time to get to speak to more people though
     

    Attached Files:

    Albrecht, atomman, tyroguru and 4 others like this.
  15. moggy240

    moggy240 INSURANCE VALUATIONS OFFICER Staff Member Moderator

    Thanks.
    It should say roughly the same as the other side but in Japanese.
     
    tyroguru likes this.
  16. Bazzateer

    Bazzateer
    Z Club Member

    Oh yes!
    I did, nice run down took 4 hours (inc comfort break) and averaged 33mpg.
    Coming back today took longer as I decided to take a more scenic route.
     
  17. Fairlineguy

    Fairlineguy
    Z Club Member

    Picked up the l28 block from being rebored.
    Refitted the crank which has been reground should get the kameari pistons fitted tomorrow
    What a lot of expense for no power gain. Lol
     

    Attached Files:

    Mark N likes this.
  18. jonbills

    jonbills
    ZClub Administrator
    Moderator

    Think how beautiful it is on the inside!
     
    Fairlineguy likes this.
  19. franky

    franky Well-Known Forum User

    did you overbore?

    Where did you take it in the SW?
     
  20. Fairlineguy

    Fairlineguy
    Z Club Member

    Just went for 87mm overbore engine was producing good power prior to going pop.
    I’ve been using Dave at DY engine services he’s into Nissan engine in a big way

    https://www.dyengineservices.co.uk/
     

Share This Page