FORD Mk2 RS2000

zedwizz

Well-Known Forum User
After being made redundant in 2009 in decided to start working for myself. Lucky I already had a workshop that I used to tinker about in doing my own projects so I was all set. I rebuilt a few engines for people and done the odd service here and there then In August 2010 I was asked to restore an Mk2 Escort RS2000 custom, which was described as being one step away from being broken for spares.

This particular vehicle had been brought as a project to restore by the pervious owner but unfortunately due to other commitments he never found the time to give it the attention it needed. So for some fourteen years this car stood under a lean-to with the passenger side exposed to the elements before the current owner stumbled across it and decided to bring it back to its former glory.

I hope you enjoy the pictures

Arrival

I took delivery of the RS2000 Custom. It arrived on the back of a transporters and at first glance didn’t look to bad so it was pushed into the workshop for a closer inspection.

f2f1b09b.jpg

fbdfcaa6.jpg

7ced689d.jpg

91970edf.jpg


Initial inspection

Once under the lights of the workshop it was easy to see which side of the car had seen fourteen winters and fourteen summers. I removed some of the outer panels to find the shell was in bad shape with the worst of the rust on the passenger side but lucky the chassis rails were in surprisingly good condition. After I report my findings I was given the go a head to start work but I could see that this was going to be a major restoration inside and out.

1299e3db.jpg

8629a9ae.jpg

b97df800.jpg

2d8188f4.jpg

802b1901.jpg

27af9e3b.jpg

a311ddff.jpg

ddab3183.jpg

1b6b3691.jpg

18b981c9.jpg

3f8becf7.jpg


Strip out

The vehicle arrived at the workshop has a complete car and with a boot full of spare parts the pervious owner had collected over the years but had never fitted. The escort was stripped down to a bare shell and a list of replacement panels and parts was made.

fccd01f3.jpg

ea2b5b34.jpg

bf0c8caa.jpg

e207c972.jpg

9d2c1555.jpg


Engine Bay

It was decided that the engine bay was the worst part of the vehicle so that’s where I started. Due to the availability/lead time of some panels I would have to replace what I could with new panels and fabricate the rest. I removed the wings, front panel, slam panel, battery tray, radiator mounts and front cross member. Apart from the tops and front edges the inner wings seemed to be in good condition so replacement tops panels were ordered.

4f90e90a.jpg

cb4518ff.jpg


The front suspension mounts and chassis rails also looked serviceable but sadly this could not be said for the bulkhead. The top of the bulkhead on the passenger side had rusted through and the drivers side had some poor repair work carried out at some stage this will require and new or second-hand panel.
 

zedwizz

Well-Known Forum User
3bcfb0d2.jpg

55ec9497.jpg

6c79408a.jpg

cff83c34.jpg


Once all the old panels where removed a jig was made to relocate all the new panels and hold everything square.

be7bb1aa.jpg

31b2cbec.jpg

8448ce07.jpg

00547cc6.jpg

0578b0a7.jpg

d7eab130.jpg

134dcb96.jpg

ca4869a0.jpg

97c62ccf.jpg


Front bumper mounting lugs and front edges patterns were produce using my CAD system. The patterns were transferred to mild steel cut out, formed and welded into position.

fdac008f.jpg

ed881d9b.jpg

ac624729.jpg

38b8f762.jpg

d2062e86.jpg

c99bb599.jpg

b7c19475.jpg

753f2030.jpg


more to follow...
 

zedwizz

Well-Known Forum User
Some more pictures...

241eed99.jpg

6f451be9.jpg

006a7869.jpg

0f8cd93c.jpg

2f200660.jpg

41b687a8.jpg

e3726a29.jpg


A second hand A post was supplied. Not in the best condition but I’ve got a welder and a big hammer.

64b7c70e.jpg

23aa23ff.jpg

e2add2c9.jpg

3a397921.jpg

b5ffe011.jpg


Now get graft it in to the car

74fa923c.jpg

acdfd307.jpg

10458af3.jpg

c9f1f4ce.jpg

9778797d.jpg
 

zedwizz

Well-Known Forum User
Next was to remove the bulkhead top panel and start patching the bulkhead and gearbox tunnel. I wanted to make it look as original as possible and not like a patchwork quilt.

74fa923c.jpg

7cdea730.jpg

948e8f38.jpg

9522e75c.jpg

cf0be19c.jpg

dd3735c9.jpg

30b56ddd.jpg

24a7b99b.jpg

c3b41cbb.jpg

e88bccbb.jpg


A goodish bulkhead top panel was found but needed a lot of prep work to fit.

248b7fc3.jpg

1b9925bb.jpg

b7076d09.jpg


Then a test fit of the outer panels just to make sure everything is still straight.

008b2aeb.jpg

89525df6.jpg

0523313c.jpg

9cb66ae3.jpg
 

zedwizz

Well-Known Forum User
Bit more done today.

The bulkhead supplied was cut from a donor so some repair work was need on the edges and then it was welded into place.

fbe73fc4.jpg

58a957a5.jpg

51f5a170.jpg

3d7a93d8.jpg

19fbe2e7.jpg

5db06b9e.jpg

b64fcca7.jpg

98b352c1.jpg


Test fitted the bulkhead splash panels a found that one was shorter than the other! More work…

ec3a0890.jpg

3caa8e5b.jpg


Lucky the donor bulkhead supplied had a dashboard in good condition still attached but because it was out of a ‘lesser’ Mk2 I had to cut out a hole for the glove box. lol

e9defb01.jpg


Finished of by making a corner patch for the passenger floor.

bdcea971.jpg

62553c86.jpg

d48add3d.jpg


more tomorrow…
 

zedwizz

Well-Known Forum User
Bit more rust replacement management…

Fitted the corner patch for the passenger floor. Still needs a bit of grinding..

6de5db3a.jpg


More patch work. The passenger side of the bulkhead was really bad.

898ad3eb.jpg

eda10c74.jpg

5bf81736.jpg

9d1b3f52.jpg


Couldn’t find anyone supplying the ‘Z’ section reinforcing brackets that attach to the bulkhead splash shields so made my own…

Old one
d0358224.jpg


New one
ea5f390a.jpg


Spot-welded to the panel
a6d6d9d6.jpg


Panel cut in and tack welded into position
f6d4ebac.jpg

1a0d47e2.jpg

1e88194e.jpg


one more patch to make tomorrow to finish the passenger side.
 

zedwizz

Well-Known Forum User
Bit more done…

One more hole to fill in the passenger floor
cbcb7200.jpg


Template made
30380b93.jpg


Patch cut out
19740b6a.jpg

549360e0.jpg


Angle of the floor section checked
c554845a.jpg


Bending to suit
530b1136.jpg

d5a2f2c9.jpg


Trimmed and welded in place
1bb036c5.jpg

a8a68b7e.jpg

d0487050.jpg
 

zedwizz

Well-Known Forum User
Bit more done to the old girl.

A bit of a rethink on the near side inner wing. On first inspection of the near side suspension struts all seemed salvageable but after dressing the inner wing to remove some dents it was found that the reinforcing plates fitted to the bottom of the struts had rusted beyond repair and sections of the inner wing needed attention so quickest way would be to remove the lot and replace with new steel.

7e7d3fc0.jpg


I decided to remove a large section of the inner which got rid of most of the rust and a load of unwanted holes someone had drilled to mount an alarm system. Luckily the chassis rail and all its inner strengtheners were in good shape.

0183a015.jpg


Rust treatment

b9a5bc0a.jpg


More patches…

4d09e030.jpg

556a8254.jpg


Had to put a bit a form into the next patch to match the inner wing profile.

91f22fac.jpg

536b86d6.jpg


Finished of by drilling the holes of the brake lines and a little paint to stop the rust before spot welding.

eda4698d.jpg

162a7aeb.jpg

e880c312.jpg


Finally tack welded in place.
0ce4d4e4.jpg

804db853.jpg


Tomorrows job is to fit the new struts…
 

zedwizz

Well-Known Forum User
Had a bit of a mission fitting the new struts and reinforcement angles today so its been a long day. First thing was to tidy up the struts themselves i.e getting rid of the ripples on the flanges.

b83d4446.jpg

6344c915.jpg


Then getting the struts to fit the profile of the inner wing and making the reinforcement angles to fit the struts.

a41dc015.jpg

cb056c8c.jpg

e302327f.jpg


Then spot weld the whole assembly together.

5c432dc5.jpg

cb68e39a.jpg

825dd2a1.jpg

155fd814.jpg


Then fitted into place ready to weld to the car.

2e89fe20.jpg
 

zedwizz

Well-Known Forum User
Took a few weeks off from the Mk2 resto to catch up with some other work I needed to finish so now that’s all done lets get this Mk2 back on the road.

Finished of the n/s/f suspension strut and completes the work on that side of the engine bay.

d6f889f9.jpg

4f1afc82.jpg


Now for the other side. I cut out some sections of rust in the inner wing and found the inner chassis rail strengthening was in poor condition so all this had to be replaced.

I made the replacement strengtheners from 16 SWG steel, bent a flange on each edge and welded it in.

e39cf70b.jpg

0d135331.jpg

a0744109.jpg

10e91633.jpg

b13eae12.jpg


then repaired the inner wing.

035c03e1.jpg

a9acd559.jpg

2522216f.jpg


The body strengthening kit turned up in the post so I made a start fitting the parts.

f069c24c.jpg

13b83886.jpg


The old girl is really coming together now and the shell has regained its structural strength so the next job will be to weld the front end on and mount the shell on the rollover jig so I can start on the floors.

The primer, etch primer, stone guard etc has been ordered together with 5 litres of midnight blue. I am really looking forward to seeing the car in paint.
 

zedwizz

Well-Known Forum User
Quick update on the RS2000 resto. This week I have been concentrating on getting the metal work finished on the bonnet, boot and doors. The boot has been replaced with a good second hand part, which only needed a small dent removing and a quick DA down. The bonnet need a bit more work mainly around the inner frame and the underside of the bonnet skin. The driver’s door has been replaced with a second hand part, which needed the bottom corners repairing, and a new door skin fitted (forgot to take any pictures). The passenger door has been replaced the second hand part also but needed a little more TLC.

b83857ff.jpg

ec7a04c5.jpg


Seems this door had a nice coat of white paint on it but unfortunately it was the kind of paint you would put on your skirting boards not on your car!

10bb856d.jpg

eadcbb3e.jpg

7e09db97.jpg

c0f49101.jpg

ed9f2c8b.jpg

68d8b3dc.jpg

4059a7f1.jpg


The repairs..
838e1564.jpg

e8db3411.jpg

d2c279e5.jpg

68de0ed8.jpg

2e4d62ae.jpg

2eb518ba.jpg
 

johnymd

Club Member
Good work, should be a Z though.

Noticed your only a few miles from me. We'll have to compare Z's.
 

moggy240

Insurance Valuations Officer
Staff member
Club Member
i have got my car on a rollover jig very similar to yours ,makes life so much easier when do welding etc.
great job by the way !!!!!!!!!!!!!!!!
 

zedwizz

Well-Known Forum User
i have got my car on a rollover jig very similar to yours ,makes life so much easier when do welding etc.
great job by the way !!!!!!!!!!!!!!!!

the rollover jig is a great tool and allows you to get a better angle of attack if you no what i mean. Nothing worse than laying on your back welding lol
 

Wyn

Club Member
Spot on :cheers:

I think you might have your work cut out should you decide to rustor Zeds aswell as ol Fords lol
Could be a good game to be in with those skills :thumbs:
 

datsfun

Club Member
You sir are a legend....:bow: Amazing welding and fabrication skills.

And they say that Japanese cars are rust buckets:rolleyes:
 
Top