Robbie J
Club Member
besides the bulkhead, there is little between the sills box section and the tubes that run down the top of the wings. I was going to get it scanned and stress-tested but really want it sprayed...
-
The Z Club relies on the support of it's paid members - join the club or renew your membership here.
280Z with RB25DET build
- Thread starter Robbie J
- Start date
Robbie J
Club Member
Done a real nice job of that Radiator, oil cooler, condenser and intercooler setup! Exactly the same setup i'm planning to use on my build so any advise you can give on which bits you used and where they came from would be a HUGE help
brackets off the powder coat
Rad was from Radtec, the intercooler is CX racing https://www.cxracing.com/KIT-RB25-STOCK-240Z-IC29?search=rb25 intercooler
and Hallie will need to help with the aircon.
The oil cooler was a stock item, I will dig out the size
Robbie J
Club Member
the Rad took a long time (lockdown) if you say what it's for they should know https://www.radtec.co.uk/
hallie
Club Member
https://www.t7design.co.uk/ac-condenser-radiator-593-x-250mm-30311344cp.html
That is the condenser I used. I couldn't fit anything larger in
That is the condenser I used. I couldn't fit anything larger in
Garaculas
Club Member
Thanks for the info gents, spoke to DJ at radtec and got all the info for the radiator. Also thinking of killing 2 birds with 1 stone and asking them to also make an FMIC whilst they're at it as it'll likely be a similar cost by the time i've paid all the imports etc on the CX racing one.
From what i can measure a 27x13x3" FMIC would fit so could even get that from Mishimoto as their M-Line model is that size. Could you measure up the size of the core of the CX racing one Robbie just so i know i'm somewhere close on my measurements? The pictures showing yours fitted is a big help too to get the end tank positions etc correct
From what i can measure a 27x13x3" FMIC would fit so could even get that from Mishimoto as their M-Line model is that size. Could you measure up the size of the core of the CX racing one Robbie just so i know i'm somewhere close on my measurements? The pictures showing yours fitted is a big help too to get the end tank positions etc correct
Last edited:
Robbie J
Club Member
hopefully, Hallie can have a look at the sizes. Not seen the car for 6 months :-(Thanks for the info gents, spoke to DJ at radtec and got all the info for the radiator. Also thinking of killing 2 birds with 1 stone and asking them to also make an FMIC whilst they're at it as it'll likely be a similar cost by the time i've paid all the imports etc on the CX racing one.
From what i can measure a 27x13x3" FMIC would fit so could even get that from Mishimoto as their M-Line model is that size. Could you measure up the size of the core of the CX racing one Robbie just so i know i'm somewhere close on my measurements? The pictures showing yours fitted is a big help too to get the end tank positions etc correct
LiamR
Club Member
CX racing one is just a cheap chinese one. Readily available on ebay.
https://www.ebay.co.uk/itm/163544634687
I have the same sized one but with 2.5inch inlet/outlet.
*edit*
Or this one which currently has an ebay sale of 10% off and its painted black for a hidden look.
https://www.ebay.co.uk/itm/UNIVERSA...-/150690237632?_trksid=p2349624.m46890.l49292
https://www.ebay.co.uk/itm/163544634687
I have the same sized one but with 2.5inch inlet/outlet.
*edit*
Or this one which currently has an ebay sale of 10% off and its painted black for a hidden look.
https://www.ebay.co.uk/itm/UNIVERSA...-/150690237632?_trksid=p2349624.m46890.l49292
hallie
Club Member
the cxracing one has a 500 mm core
Robbie J
Club Member
No only on the GTR forum. I bagged first dibs in a hour... 498BHP at the wheels. It needs work and decent brakes!
It looks great.
