Search results

  1. 240L31

    Preload rear wheel bearings

    Hey guys, I replaced my rear wheel bearings and torqued the axle nut to 290Nm. Is it common that the axle feels rather stiff? I measured around 1000g with a fish scale to start axle rotation (FSM spec: 750g).
  2. 240L31

    Alternative axle nut

    While rebuilding my suspension, I was looking for an alternative axle nut (rear). Original one is peened type (PIA) 280ZX one is pinched type (upon removal, it destroyed the threads of the stub axle) Following part number is a perfect fit and far better than the 280zx option: 7703034250...
  3. 240L31

    P90 Cylinder Head for sale

    Cylinder head P90, not shaved. Clean but needs a valve job (lapping could be enough, though). 550€
  4. 240L31

    Datsun competition coilover info

    Hey, I am currently trying to get my BC coilovers street legal. My local inspector asks for further info about the original coilovers which (I think) were part of the Datsun competition program. Anything helps, pictures, catalogue pages, drawings.. especially spring rates were requested...
  5. 240L31

    SOLD: Series 1 air filter box

    Rare non-flapper series 1 air filter box. No rust or dents, includes bolts. 300€ obo
  6. 240L31

    L series bellhousing for s12/s13 gearbox conversion

    Due to a change in plans I no longer will need my spare L6 bellhousing. It is cleaned and glass bead blasted. It can be used to convert a s12/s13/s14 box. One of the best upgrades I had on my car! Picture on request, it's currently stored at work. 300€
  7. 240L31

    Valve stem seals bad after 15.000 Km?

    Hey guys, Last week I was told that there are blue clouds of smoke during deceleration and tip-in. Whats your experience, could this be the valve steam seals already? The engine was rebuild 15.000 Km ago. Which are the best available valve stem seals? OE? Victor Reinz? Thanks :)
  8. 240L31

    Gearbox removal on Jack stands

    Hey, Did anyone try to remove the gearbox without a lift (car on jack stands)? I might have to go that route soon.. Thanks!
  9. 240L31

    Power brake booster interchangeabiltiy

    Hey, will a later model 240Z power brake booster ( 8 1/2") fit in an earlier model (with 7" booster)? In other words, is the firewall bolt pattern the same? Thanks - I couldn't find a definitive answer for this:)
  10. 240L31

    Kyosan Denki Fuel Pump Rebuild

    As my electrical fuel pump installation failed due to too little flow, I decided to rebuild the stock mechanical fuel pump. I ordered OEM parts but still had a similar looking american fuel pump. As I was curious, I took it apart and pictured the differences. Findings: - Castings are identical...
  11. 240L31

    Fuse box cover bulb type

    Does anyone know the exact name of the tiny fuse box lights (Choke, fasten seatbelts..)? There's only 12V/1,5W written on mine. Thanks!
  12. 240L31

    Subaru R180 CLSD rebuild

    Hey guys, I just bought a set of new friction plates for my Subaru R180 3.9 LSD (Black Friday sale). My diff features a lot of backlash (around 0.19 which is exactly at the upper spec), therefore I wanted to open it up anyways. While I am at it it's not too much work to replace the clutch...
  13. 240L31

    Mechanical fuel pump fitting size

    Guys, does anybody know what thread size the mechanical fuel pump fittings are? 1/4" pipe thread for sure - but NPT or BSP? I want to replace the 90° elbow by an 1/4" to 8mm adapter. Right the fuel pump side requires a 6mm fuel line, whereas the fuel filter (and hard line below) need a 8mm...
Top