No username? Register here.
Go Back   ZClub.net > General > General discussion

Reply
 
Thread Tools Display Modes
  #16  
Old 22-07-2017, 01:04 AM
Woody928's Avatar
Woody928 Woody928 is offline
Z Club member
Third gear
 
Join Date: Jun 2016
Location: Surrey
Posts: 422
Member 1093
Put me down for some please.
__________________
1971 Datsun 240z - L26 - 918 Orange
Reply With Quote
  #17  
Old 22-07-2017, 01:19 AM
uk66fastback's Avatar
uk66fastback uk66fastback is offline
Z Club member
Fourth gear
 
Join Date: Mar 2015
Location: Peterborough
Posts: 1,316
Member 1052
Apparently looking around the 'net getting these OUT is one of the worst jobs ... some speak about a tool that does the job ... are they really that bad?

I better have a set on the shelf just in case, so add me too please.
__________________

Mike
1972 240Z US LHD ...
Reply With Quote
  #18  
Old 22-07-2017, 07:15 AM
status status is offline
Website member
Sixth gear
 
Join Date: Mar 2002
Location: Pledgdon Green
Posts: 3,136
Had to burn a set out of my z once,changed suspicion a few times since and was ok,I have one spare at home but always worth having a set knocking around
Reply With Quote
  #19  
Old 22-07-2017, 09:20 AM
Red7 Red7 is offline
Website member
Third gear
 
Join Date: Mar 2015
Location: Nottinghamshire
Posts: 378
I'll have a set too Franky please for the shelf just in case, thanks
Reply With Quote
  #20  
Old 22-07-2017, 09:33 AM
franky franky is online now
Z Club member
Sixth gear
 
Join Date: Sep 2011
Location: usually work
Posts: 3,289
Member 770
updated.
Reply With Quote
  #21  
Old 22-07-2017, 10:07 AM
Red7 Red7 is offline
Website member
Third gear
 
Join Date: Mar 2015
Location: Nottinghamshire
Posts: 378
Quote:
Originally Posted by franky View Post
updated.

Franky when do you want paying? I'm on holiday from next Friday until 15th August, I can pay you before I go if you like
Reply With Quote
  #22  
Old 22-07-2017, 10:29 AM
franky franky is online now
Z Club member
Sixth gear
 
Join Date: Sep 2011
Location: usually work
Posts: 3,289
Member 770
Quote:
Originally Posted by Red7 View Post
Franky when do you want paying? I'm on holiday from next Friday until 15th August, I can pay you before I go if you like
Hi - No rush. I don't pick them up till next Friday.
Reply With Quote
  #23  
Old 22-07-2017, 11:03 AM
Red7 Red7 is offline
Website member
Third gear
 
Join Date: Mar 2015
Location: Nottinghamshire
Posts: 378
Quote:
Originally Posted by franky View Post
Hi - No rush. I don't pick them up till next Friday.

Sound
Reply With Quote
  #24  
Old 22-07-2017, 01:10 PM
Farmer42's Avatar
Farmer42 Farmer42 is offline
Z Club member
Third gear
 
Join Date: May 2014
Location: Downend, Bristol
Posts: 457
Member 979
Hi Jason

I will need to change the rear bushes at some point in the near future so could you please put me down for a pair.

Thanks

Paul
__________________


1975 Fairlady Z 2+2
Reply With Quote
  #25  
Old 22-07-2017, 01:26 PM
atomman atomman is offline
Website member
Third gear
 
Join Date: Feb 2013
Location: swansea
Posts: 434
I'm interested in a spare pair to,

Can I ask what material spec they are made out of though ? EN24T ? and are they yellow passivated like the OG pins?
Reply With Quote
  #26  
Old 22-07-2017, 03:01 PM
uk66fastback's Avatar
uk66fastback uk66fastback is offline
Z Club member
Fourth gear
 
Join Date: Mar 2015
Location: Peterborough
Posts: 1,316
Member 1052
I'd be interested in anyone's tips about getting these out - maybe a marinade in WD40. I wouldn't think anyone has removed the ones on my car in the past.
__________________

Mike
1972 240Z US LHD ...
Reply With Quote
  #27  
Old 22-07-2017, 03:38 PM
jonbills's Avatar
jonbills jonbills is online now
Z Club member
Fifth gear
 
Join Date: Sep 2005
Location: M6
Posts: 2,403
Member 254
Quote:
Originally Posted by uk66fastback View Post
I'd be interested in anyone's tips about getting these out - maybe a marinade in WD40. I wouldn't think anyone has removed the ones on my car in the past.


Take the lockpin thing out, take the nuts and washers off the spindle, put a shallow socket or short bit of tube over the threaded end of the spindle, get a nut on the spindle end, tighten the nut slowly pulling the pin through the socket as much as you can, repeat with a longer socket/bit of tube until done ✅
__________________
1974 260z
Reply With Quote
  #28  
Old 22-07-2017, 04:14 PM
Bobafett Bobafett is offline
Website member
Second gear
 
Join Date: Mar 2016
Location: West Kirby, Wirral
Posts: 80
Set for me please if I'm not too late to the party.

Cheers.
Reply With Quote
  #29  
Old 22-07-2017, 06:13 PM
franky franky is online now
Z Club member
Sixth gear
 
Join Date: Sep 2011
Location: usually work
Posts: 3,289
Member 770
I'll have to close the list for now.

Thanks all.
Reply With Quote
  #30  
Old 22-07-2017, 11:49 PM
Moriarty Moriarty is offline
Website member
Second gear
 
Join Date: May 2012
Location: A Waterfall
Posts: 93
Quote:
Originally Posted by Turn & Burn View Post
The local engineering supplies company, 5 cash for two.
They're not stainless, just high tensile, I work with stainless and must say I'm not really a fan either. It's alright for show, but I wouldn't generally use it for structural stuff.
Some grades of stainless will pick up or gall when continually run in a high carbon steel or iron guide.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 08:34 PM.

The Future Is Bright... The Future Is ZClub!

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Copyright ZClub.net, All Rights Reserved.