Search results

I believe this to be a 'Mangoletsi' manifold based on previous posts/research - it has the casting number '4700' in the middle bracing. It is in very good clean condition. The carburettor-side ports measure 45mm diameter. £275 plus Royal Mail 48 postage cost based on package weight.

In good solid condition with surface rust only. The two outlet pipes have a diameter of approximately 48mm / 1.875". Ideally for use with cylinder heads which have round exhaust ports (N47 P79 P81) although this was successfully used on my 240Z square ported head. £80 collection from Solihull...

In good useble condition with front bearings included. £30 + postage.

Nice and clean, no dents but have a few surface scratches as can be seen in the photos. They fit the 240Z carbs perfectly and measure 70mm long and 68mm inside diameter at the end. Very light weight - presume they are made from aluminium ? £20 plus £2.88 Yodel postage.

Hi, I'm after some guidance on a strut cartridge please. The Nissan part number is 56210-E8126 and I've attached some photos. I could only find the attached reference table on this website www.jdmjunkies.ch. So it appears to be a firm/hard suspension cartridge for Europe but for use in...

Hi all, I have a set of replacement L24 pistons/con-rod assemblies but noticed that one of them has got several indentation/impact marks restricted to a small area between piston top and between the ring grooves - see photo. No idea how this happened - probably was there when I bought them some...

Can someone please explain what the parts high-lighted in yellow do. The S30 parts illustrations I have (attached) dont show these extra parts. Please post any illustrations if you have one. Thanks in advance.

Are there any suppliers of reproduction seal gaskets?

I have numerous items currently on Ebay for 240Z/260Z/280Z - please follow link the below if you are interested...

I purchased a new SKF 13978 oil seal from Rockauto but when I fitted it today it literally just slid in without giving much resistance at all. Now the manual says to use an oil seal drift so there should be some resistance when installing it obviusly to ensure that there is a good seal so I'm a...

Need some guidance regarding the replacement of the small o-rings please. The atttached guidance referes to the o-ring (part no. 3) being 'triangular'. I'm not sure whether this is true or whether the existing one in the picture has just been deformed to this shape due to the chamfered edges on...

Does any one know where the 'washer-special D' part 15 is located and its dimensions please? Thanks

Mine are corroded and NLA from Nissan. Does anyone know of a decent substitute or perhaps have some for sale? Cheers

Has anyone been able to get the lever rechromed without disassembling the mechanism which is pressed and welded together ? Mine is rusted in parts and generally pitted. Not sure what's possible with the process itself i.e. 'masking off'. Any alternative techniques to make it look tidy? Thanks

On the assembly drawing there are clevis pins shown at the top of each pedal but I can't remember any being there when it was stripped down (some time ago), and I can't find them so what are they there for? They are not for the springs as they go directly into the pedal. Thanks

Continuing my parts clear out and came across these two items. Do they look familiar to anyone? Thanks

Doing a garage clear out and came across these. Are they of use to anyone?

https://www.ebay.co.uk/itm/373232669750

Hi All, I'm after some help to identify the correct car model for this rad support panel that I've had stored for some time now. The Nissan part no. is 62500-N4500. I've looked at a copy of the fiche I've got but it's not listed. I thought parts with the code N30 to N49 were S30 but it does not...

I have listed a number of 240Z/260Z items on Ebay if anyone is interested. I am not looking for offers at the moment as I'll initially let the auctions run for a week. Thanks. https://www.ebay.co.uk/itm/373161697277 https://www.ebay.co.uk/itm/373161753906...